View MT185GW01-V2_7688827.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

innolux copyright all rights reserved, copying forbidden. record of revision version revise date page content 1.0 2008/11/10 initial release
spec no. mt185gw01 v.2 page 2/22 contents: a. general specification b. electrical specifications 1. pin assignment 2. absolute maximum ratings 3. electrical characteristics a. typical operating conditions b. display color vs. input data signals c. input signal timing d. display position e. backlight driving conditions c. optical specifications d. reliability test items e. safety f. display quality g. handling precaution h. label i. mechanical drawings appendix
spec no. mt185gw01 v.2 page 3/22 a. general specification no. item specification remark 1 display resolution (pixel) 1366(h) x 768(v), wxga resolution 2 active area (mm) 409.8(h) x 230.4(v) 3 screen size (inch) 18.5 inches diagonal 4 pixel pitch (mm) 0.3(h) x 0.3(v) 5 color configuration r, g, b vertical stripe 6 overall dimension (mm) 430.37 (w) x 254.6 (h) x 16.5 (d) (max.) 7 weight (g) 2100 (max) 8 surface treatment anti-glare, haze=25%, hard coating (3h) glare optional 9 input signal interface one channel lvds interface 10 display colors 16.7m (6 bit with hi-frc) 11 color saturation 72% ntsc 12 optimum viewing direction 6 o?clock 13 rohs & halogen free rohs compliance & halogen free
spec no. mt185gw01 v.2 page 4/22 b. electrical specifications 1.pin assignment connector jae fi-xb30ssl-hf15 or mechanical interface equivalent connector.
spec no. mt185gw01 v.2 page 5/22 rear view of lcm
spec no. mt185gw01 v.2 page 6/22 2. absolute ma ximum ratings values parameter symbol min. typ. max. unit remark power volta g e v cc -0.3 - 6.0 v a t 25c in p ut si g nal volta g e v lh -0.3 - 4.3 v a t 25c o p eratin g tem p erature to p 0 - 50 c note 1 stora g e tem p erature t st -20 - 60 c note 2 ccfl current icfl 2 7.5 8 [ ma ] note 1: the relative humidity must not exceed 90% non-condensing at temperatures of 40c or less. at temperatures greater than 40c, the wet bulb tem perature must not exceed 39c. note 2: the unit should not be exposed to corrosive chemicals.
spec no. mt185gw01 v.2 page 7/22 3. electrical characteristics a. typical operating conditions item symbol min. typ. max. unit remark input voltage v cc 4.5 5 5.5 v permissive power input ripple v rf - - 0.15 v black i cc - 700 1000 note 1 white i cc - 500 700 note 2 input current mosaic i cc - 700 1000 ma note 3 rush current i rush - 1.6 3 a note 4 common mode voltage vcm - 1.2 - v differential input voltage vid 100 - 600 mv threshold voltage (high) vth - - 100 mv note 5 logic input voltage lvds: in+, in- threshold voltage (low) vtl -100 - - mv note 5 note 1 : the specified current is under the vcc =5v, 25 c, fv=60hz (frame fr equency) condition whereas black pattern is displayed. note 2 : the specified current is under the vcc =5v, 25 c, fv=60hz (frame frequency) condition whereas white pattern is displayed. note 3 : the specified current is under the vcc =5v, 25 c, fv=60hz (frame frequency) condition whereas mosaic pattern(black & white [8*6] ) is displayed. white : 255 gray black : 0 gray
spec no. mt185gw01 v.2 page 8/22 note 4 : test condition :? (1) v dd = 5 v, v dd rising time = 470 s 10% (2) pattern: mosaic pattern (3) test circuit note 5: lvds signal definition vid = vin + ? vin- , ? vcm = x vcm + ?vcm- x , ? vid = x vid + ?vid- x , vid+ = x vih + ?vih- x , vid- = x vil + ?vil- x , vcm = (vin + +vin-)/2, vcm+ = (vih + +vih-)/2, vcm- = (vil + +vil-)/2, 90 % ton=470 ? s ? 10% v dd 5 v 12v v dd ( lcd input) control signal (high to low) m2 2sk1399 m1 2sk1059 r2 1k c2 10000pf c3 1uf r3 47k r1 47k fuse c1 1uf vin + = positive differential data & clk input vin- = negative differential data & clk input
spec no. mt185gw01 v.2 page 9/22 note 6 : power on sequence for lcd v dd parameter value unit min typ max ms t1 0.1 - 10 ms t2 0 30 50 ms t3 200 250 - ms t4 100 250 - ms t5 0 20 50 ms t6 0.1 - - ms t7 1000 - - ms 90% 90% 90% 90% 10% 90% 90% t2 t3 t4 t5 t6 t7 v alid interface data 10% 10% interface signals panel power supply v dc backlight power supply t1
spec no. mt185gw01 v.2 page 10/22 b. display color vs. input data signals the brightness of each primary color (red, green and blue) is based on the 8-bi t gray scale data input for the color; the higher the binary input, the brighter the color. the table below provides a reference for color versus data input. color input color data red green blue msb lsb msb lsb msb lsb r7 r6 r5 r4 r3 r2 r1 r0 0 1 0 0 0 1 1 1 black red(255) green(255) blue(255) cyan magenta yellow white 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 basic colors 0 0 0 : 1 1 1 red(000) dark red(001) red(002) : red(253) red(254) red(255) bright 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 red 0 0 0 : 0 0 0 green(000)dark green(001) green(002) : green(253) green(254) green(255) bright 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 green 0 0 0 : 0 0 0 blue(000) dark blue(001) blue(002) : blue(253) blue(254) blue(255) bright 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 blue 0 1 0 0 0 1 1 1 0 0 1 : 0 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 1 0 0 0 1 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 g7 g6 g5 g4 g3 g2 g1 g0 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0
spec no. mt185gw01 v.2 page 11/22 c. input signal timing support input timing table item description min. typ. max. unit period 10.5 13.2 15.9 ns clock dclk frequency 62.9 75.4 95.6 mhz t v_total v total line number 786 806 900 t h_total t v_data data duration ? 768 ? t h_total t vb v-blank 18 38 132 t h_total vertical f v frequency 50 60 76 hz t h_total h total pixel number 1400 1560 1800 dclk t h_data data duration ? 1366 ? dclk horizontal t hb h-blank 40 194 434 dclk note: because this module is operated by de only mode, hsync and vsync input signals should be set to low logic level or ground. otherwise, this module would operate abnormally. data
spec no. mt185gw01 v.2 page 12/22 d. display position d(1, 1) d(2, 1) ?? d(683, 1) ?? d(1365, 1) d(1366, 1) d(1, 2) d(2, 2) ?? d(683, 2) ?? d(1365, 2) d(1366, 2) . . . ?? . . . ?? . . . . . . d(1, 384) d(2, 384) ?? d(683, 384) ?? d(1365, 384) d(1366, 384) . . . ?? . . . ?? . . . . . . d(1, 767) d(2, 767) ?? d(683, 767) ?? d(1365, 767) d(1366, 767) d(1, 768) d(2, 768) ?? d(683, 768) ?? d(1365, 768) d(1366, 768) e. backlight driving conditions parameter symbol min. typ. max. unit remark remark lamp voltage vl - 700 - vrms i=7.5ma note 1, 2 lamp operation current il 2 7.5 8 marms note 3 1300 - - t = 25c note 4,5,6,7 lamp starting voltage vlstart 1700 - - vrms t = 0c note 4,5,6,7 frequency f 40 - 60 khz note 7 lamp life time 50000 - - hr note 8 note: the waveform of the voltage output of inverter must be area-symmetric and the design of the inverter must have specifications for the modularized lamp. the performance of the backlight, such as lifetime or brightness, is greatly influenc ed by the characteristics of the dc-ac inverter for the lamp. all the parameters of an inverter should be carefully designed to avoid producing too much current leakage from high voltage output of the inverter. when designing or ordering the inverter please make sure that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. if the above situation is confirmed, the module should be operated in the same manners when it is installed in your instrument. note 1: specified values are for a single lamp. note 2: operating voltage is measured at the condition of ta = 252c. the variance of the voltage is ? 10%. note 3: the degree of unbalance: less than 10% the ratio of wave height: less than 10% 2 the degree of unbalance = |ip-i-p| /irms*100(%) the ratio of wave height = ip (or i-p)/irms lamp should be completely turned on. ip i-p ip: high side peak i-p: low side peak
spec no. mt185gw01 v.2 page 13/22 note 4: test equipment: as-114b note 5: the voltage shown above should be applied to the lamp for more than 1 second after startup. otherwise, the lamp may not be turned on normally. note 6: inverter should provide more than min. va lue, and then lamp could be completely turned on. note 7: lamp frequency may produce interference with horizontal synchronous frequency and this may cause line flow on the display. therefore lamp frequency shall be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. note 8: life time (hr) is defined as the time when br ightness of a lamp unit itself becomes 50% or less than its original value at t he condition of ta = 252c and i l = 7.5marms. backlight connecter: 3500ihs-02l pin no. symbol function remark 1 vih lamp high voltage input cable color: pink 2 vil lamp low voltage input cable color: white 3 vih lamp high voltage input cable color: blue 4 vil lamp low voltage input cable color: black
spec no. mt185gw01 v.2 page 14/22 c. optical specifications s p ecification item symbol condition min. t yp .max. unit remark tr - 1.5 4 tf - 3.5 6 response time tr+tf = 0 - 5 10 ms note 4 contrast ratio cr = 0 700 1000 - note 3,5 top cr 10 cr 70 75 80 85 - bottom cr 10 cr 70 75 80 85 - left cr 10 cr 75 75 85 85 - viewing angle right cr 10 cr 75 75 85 85 - deg. note 3,5,7 bri g htness ( center ) y l 200 250 - nit note 3,6 wx 0.313 w y 0.329 rx 0.640 r y 0.349 gx 0.284 g y 0.617 bx 0.142 color chromaticity(cie) b y = 0 -0.03 0.067 +0.03 note 3 white uniformit y ( 9 ) w 0.75 0.80 - note 3,8 cross talk ct - - 2% note 9 note 1: ambient temperature = 25c. note 2: to be measured in dark room after backlight warm up 30 minutes. note 3: to be measured with a viewing cone of 2by topcon luminance meter bm-5a. note 4: definition of response time: the output signals of bm-7 are measured when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black ? (rising time), respecti vely. the response time interval is between the 10% and 90% of amplitudes. refer to figure as below.
spec no. mt185gw01 v.2 page 15/22 note 5: definition of contrast ratio: contrast ratio is calculated by the following formula. note 6: driving cond itions for ccfl: i l = 7.5 ma, 50 khz frequency. note 7: definition of viewing angle note 8: definition white uniformity: luminance are measured at the following nine points (p1~p9). s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% contrast ratio ( cr ) = brightness on the "white" state brightness on the "black" state w = minimum brightness o f nine points ( p1~p9 ) . maximum brightness of nine points (p1~p9).
spec no. mt185gw01 v.2 page 16/22 note 9: l l a -l a? l / l a x 100%= 2% max., l a and l a? are brightness at location a and a? l l b -l b? l / l b x 100%= 2% max., l b and l b? are brightness at location b and b? note 10: optical characteristic measurement setup. 0 gray level 1/2 1/2 1/6 1/6 a b 1/2 1/2 1/6 1/6 2/3 1/3 1/3 2/3 a? b? 127 gray level 127 gray level
spec no. mt185gw01 v.2 page 17/22 d. reliability test items test item test condition judgment remark high temperature storage 60c, 240hrs note 1 note 2 low temperature storage -20c, 240hrs note 1 note 2 high temperature & high humidity operation 40c, 90%rh, 240hrs (no condensation) note 1 note 2 high temperature operation 50c, 240hrs note 1 note 2 low temperature operation 0c, 240hrs note 1 note 2 thermal shock (non-operation) -20c/1hr ~60c/1hr , 100cycles note 1 note 2 electrostatic discharge (esd) (non-operation) contact:+/-8kv, 150pf(330ohms), 25 times/1 point, 1 time/1 sec air discharge:+/-15kv, 150pf(330ohms), 25 times/1 point, 1 time/1 sec note 1 note 2 vibration (non-operation) vibration level : 1.5g bandwidth : 10-300hz waveform : sine wave, sweep rate : 10min 30 min for each direction x, y, z (1.5 hrs in total) note 1 note 2 mechanical shock (non-operation) shock level : 50g, 11ms waveform : half sine wave direction : x, y, z one time each direction note 1 note 2 mtbf demonstration 50,000 hours with confidence level 90% note 1 note 3 note1: pass: normal display image with no obvious non-uniformity and no line defect. partial transformation of the module parts should be ignored. fail: no display image, obvious non-uniformity, or line defects. note2: evaluation should be tested after storage at room temperature for one hour. note 3: the mtbf calculation is based on the assumption that the failure rate distribution meets the exponential model (ccfl excluded)
spec no. mt185gw01 v.2 page 18/22 e. safety (1) sharp edge requirements there will be no sharp edges or corners on the display assembly that could cause injury. (2) materials a. toxicity there will be no carcinogenic materials used anywhere in the display module. if toxic materials are used, they will be reviewed and approved by the responsible innolux toxicologist. b. flammability all components including electrical components that do not meet the flammability grade ul94-v1 in the module will complete the flammability rating exception approval process. the printed circuit board will be made from material rated 94-v1 or better. the actual ul flammability rating will be printed on the printed circuit board. c. capacitors if any polarized capacitors are used in the displa y assembly, provisions will be made to keep them from being inserted backwards. f. display quality the display quality of the color tft-lcd module should be in compliance with the innolux?s incoming inspection standard. g. handling precaution the handling of the tft-lcd should be in compli ance with the innolux?s handling principle standard.
spec no. mt185gw01 v.2 page 19/22 h. label (1) module label (a) model number: mt185gw01 (b) version: v.2 (c) serial id i: z 1 z 2 z 3 z 4 z 5 z 6 z 7 z 8 z 9 z 10 z 11 z 12 serial id includes the information as below: 1. manufactured date: year: 0~9, for 2000~2009 2. month: 1~9 & a~c for jan.~dec. 3. date: 1~9 & a~z (exclude i, o, q, u) for 1st~31th 4. code of grade: 1, 2, 3, 5, e 5. serial no: module manufacture sequence no (d) serial id ii (inl internal use) serial no code of grade year, month, date inl internal use inl internal use inl internal use 18 mm 73 m m mt185gw01 v.0 am1850001 2xx z 1 z 2 z 3 z 4 z 5 z 6 --z 7 -- z 8 z 9 z 10 z 11 z 12 z 1 'z 2 '-z 3 ' z 4 'z 5 'z 6 'z 7 '-z 8 ' - z 9 '- z 10 '- z 11 ' z 12 '-z 13 '-z 14 ' z 15 ' -z 16 '-z 17 'z 18 ' z 19 ' -z 20 'z 21 'z 22 ' z 23 ' made in xxx
spec no. mt185gw01 v.2 page 20/22 (2) carton label 100 mm (a) model number: mt185gw01 (b) version: v.2 (c) packing quantity: 7 pcs (d) serial id: z 1 z 2 z 3 z 4 z 5 z 6 z 7 z 8 z 9 serial id includes the information as below: (a) manufactured date: year: 0~9, for 2000~2009 month: 1~9 & a~c for jan.~dec. date: 1~9 & a~z (exclude i, o, q, u) for 1st~31th (b) code of grade: 1,2, 3, 5, e (c) serial no: module packing sequence no innolux display box id : model no. mt185gw01 v.2 am1850001 2xx quantity : 7 pcs mfg date: 20xx/xx/xx qc: made in xxx serial no code of grade year, month, date inl internal use 60 mm z 1 z 2 z 3 z 4 --z 5 -- z 6 z 7 z 8 z 9
i. me drawing (1) front view
(2) back view

▲Up To Search▲

Price & Availability of MT185GW01-V2

	To Download MT185GW01-V2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .